Supply of Mild Steel Plate, Of Size 3.15X230x25.4 Mm, Material Mild Steel Conforming To Is: 2062-2011 Or Latest With One Coat Of Red Oxide Paint. Sa Mple To Be Given For Approval Before Effecting Bulk Supply.
Supply Of M.S.Angle 75X75x6, 2.5M Long, Eye Bolt, Turn Buckle, Structure Of L.A With Plinth & Foundation, Structure Of Line Isolator With Plinth & Foundation, 33 Kv Vcb Plinth & Foundation, Structure Of 33 Kv Post Insulator With Plinth & Foundation, Chemical Pipe Earthing, Pg Clamp For Dog To Dog, Cable Stand For125x65x6 Mm For 33 Kv Cable, Control Cable Copper 4X2.5, Control Cable Copper 2X2.5, Stone Pad, 33 Kv F Clamp With Nut & Bolt, 33 Kv X-Arm Holding Clamp With Nut & Bolt, 33 Kv Number Plate, Danger Board With Clamp, Barbed Wire, Bolt, Nut & Washer, Concreting Of Support, Alluminium Binding Wire, Top Channel 125X65with Clamp, Bracing Angle 65X65x6with Clamp, E Clamp For 33 Kv, Ms Angle For Dropper 100X50x6 Mm With Holding Clamp, Bolt, Nut & Washer., Al. Paint, Redoxide Paint, Channel 100X50x6mmx2.5 M With Clamp, Clamp For Fixing Cable On Channel Of Double Poles, Gi Pipe 6 Dia, Hdpe Pipe Etc
Supply Of Dual Desk, Table, Office Table, Office Table, Meeting Table, Library Table, Computer Work Station, Library Open Book Shelf, Glassdoor Storage, Almirah, Seater Sofa, Steel Bed, Mattress, Metaltable, Dinning Table, Lab Stool, High Back Chair, Medium Back, Visitor Chair, Chair Without Arm, Metal Lockers, Magnitic White Board, Chalk Board, Ss Stop Pot, Ss Two Set Burner, Ss Single Sink, Ss Tiltting Type Bulk Cooker, Ss Tiliting Type Boiling Pan, Ss Spice Trolley, Ss Work Table, Chapati Hot Plate, Semi Automatic Chapti, Conveyer Type Toaster, Ss Four Door Vertical Chiller, Deep Freezer, Dry Masala Grinder, Pulveriser, Dough Kneader, Wet Masala Grinder, Ss Sex Vessal Hot Bain, Ss Plat Form Trolley, Ss Kitchen Utility Trolley, Ss Spot Rack Four Shelf, Ss Storage Rack Four Shelf, Hdpeplate, Potato Piller, Ss Hood, Gi Ducting, Cylinder Lpg Gas, Lpg Pipe Ling
Supply Of Raw Material -2500X1250x3.0Mm Thk Cold Reduced Carbon Steel - Crcs, 2500X1250x2.0Mm Thk Cold Reduced Carbon Steel - Crcs, 2500X1250x2.5Mm Thk Cold Reduced Carbon Steel - Crcs, 2500X1250x1.0Mm Thk Cold Reduced Carbon Steel - Crcs, 2500X1250x6.0Mm Thk Hot Rolled Carbon Steel, 2500X1250x10.0Mm Thk Hot Rolled Carbon Steel, Ismc 100 X 50 Mm Ms Channel Conforming To Is -2062, , Ismc 75 X 40 Mm Ms Channel Conforming To Is -2062, , Hexagonal Bright Steel Bar, 10 Mm Abyf, Confirming To Is-9550, Hexagonal Bright Steel Bar, 13 Mm Abyf, Confirming To Is-9550, Round Bright Steel Bar, 12 Mm Dia, Confirming To Is9550, Round Bright Steel Bar, 25 Mm Dia, Confirming To Is-9550, 3500X900x1.0 Mm Thk Aluminum Alloy Sheet Conforming, 25X25 Al Alloy Sq Bar, Designation-64430, Condition-Wp, 2500X1250x3.0Mm Thk Gi Sheet, 2500X1250x0.8 Mm Thk Crcs Perforated Sheet, Mild Steel Square Bar 12 X 12 Mm Conforming To Is - 1732, Aluminum Square Bar 19 X 19 Mm Or 20 X 20 Mm 6 Mtrs Lg, Aluminum Bar 30 X 16 Mm Or 32 X 16 Mm 6 Mtrs Lg, Aluminum Square Bar 9.53 X 9.53 Mm Or 10 X 10 Mm 6 Mtrs Lg, Aluminum Sheet 3.0 Thk Size 2400Mm X 900Mm, Aluminum Sheet 2.5 Thk Size 2400Mm X 900Mm, Aluminum Sheet 1.6 Thk Size 2400Mm X 900Mm, Ss304 Sheet 1.6 Thk Size 2500Mm X 1250Mm, Ss304 Plate 6 Thk Size 2500Mm X 1250Mm, Hexagonal Stainless Steel Bar Ss304, 10 Mm Abyf -3 Mtr Lg, Hexagonal Stainless Steel Bar Ss304, 6 Mm Abyf - 3 Mtr Lg, Mild Steel Hot Finished Seamless 5.49Mm Thk Circular Tube, Cold Rolled Austenitic Stainless Steel Sheet 2500 X1250 X1.5 Thk Etc
Procurement Of Hull Items, 951 Gi Sheet 22 G Ms L Angle 40 X 6 Mm Ms Plate 10 Mm Grinding Wheel 100 X 116X 4 Mm Ms Flat 50 X 6 Mm Ms Box Channel 40 X 75 Mm
Supply Of Steel Tubes, Tubulars And Other Steel Fittings As Per Is 1239 Part 2 - Steel Pipe Fittings Q3, Copper Alloy Gate Valve For Waterworks Purpose As Per Is 778 Q3, Pvc Cabinet Looking Mirror Of Size 600 Into 450Mm Make Shakti Or Jainko Or Prima, Ss Plate Rack Of Size 900 Mm Into 600 Mm Make Silver Shine Or Prayag Or Shakti, Ball Valves Hp Of Ptmt With Iron Pipe For 20Mm Make Shakti Or Jainko Or Sheetal, Corner Glass Shelf 30Cm Into 30 Cm With Design Cpmake Prayag Or Shakti Or Jainko, Ss Plate Rack Of 600 Mm Into 600 Mm Thickness 1Mm Make Silver Shine Or Prayag Or Shakti, Glass Shelf Cp Glass Railing 450Mm Long Make Make Prayag Or Shakti Or Jainko, Waste Coupling Of Thread 32Mm Dia Suitable For Whb Make Cera Or Shakti Or Prima, Stainless Steel Soap Dish Make Shakti Or Jainko Or Prima, Ball Valves Hp Of Ptmt Rod And Iron Pipe For15mm Pipe Make Shakti Or Jainko Or Sheetal, Ss Grating Plate 125Mm Dia Without Hole Make Silver Shine Or Prayag Or Shakti, Wast Coupling Of Cp Coated Half Ss 100Mm Into Mm Dia Make Cera Or Shakti Or Prima, Gi Union 15Mm Make Unik Or Tata Or Jindal, Cp Brass Phase Head For Bib Cock Pillar Make Shakti Or Prayga Or Jindko, Cp Push Cock 15Mm Make Shakti Or Prayga Or Jindko, Brass Spindle Half Round For Cp Bib Cock 15Mm Bore Shakti Or Prayga Or Jainko, Brass Spindle For Cp Pillar Cock 15Mm Bore Shakti Or Prayga Or Jainko, Ms Bolts 300Mm Long Plate Stove Bolt 12Mm Dia Make Classic Or Tata Or Crown, Brass Spindle Half Round For Cp Concealed Stop Cock 15Mm Bore, Alum Sliding Door Bolt With Bolt Type 250Mm Long Make Classic Or Tata Or Crown, Alum Alloy Handles 125Mm Long Make Classic Argent Crown Isi Marked, Ms Pressed Handle Black 150Mm Long Make Classic Or Crown Or Door Set, Ms Sb 250Mm Long Plate Type Stove Bolt 12Mm Dia Make Classic Or Crown Or Door Set, Butt Hinges Medium Weight Cold Rolled Ms 75Mm Long Make Classic Or Crown Or Door Set, Butt Hinges Medium Weight Cold Rolled Ms 50Mm Long Make Classic Or Crown Or Door Set, Alum Barrel Tower Bolt Of Section 200Mm Long Make Classic Or Crown Or Door Set, Brass Spindle For Concealed Stop Cock Shakti Or Prayag Or Jainko, Vitrous China Water Closet Seat Ewc White Make Shakti Or Prayag Or Prima, Ms Cp Coated Hasp And Ataple 75Mm Long Classic Or Crown Or Doorset, Ms Cp Coated Hasp And Ataple 100Mm Long Make Classic Or Crown Or Doorset
Replacement Of Corroded / Loose Rivets & Structural Repairs Of Various Members Including Side Pathway, Bed Plate & Catwalk Of Various Track Girders In Kyn-Igp Section Over
Supply, Installation Of Column Speaker Scm-15T Type With Line Matching Transformer Complete &, Fixing In Shaded/Unshaded Area With Suitable Iron Plates For Hanging And Fixing Of The Speakers As Per Direction Of Rlys Engineer. Supply And Cutting Of Iron Plates, Fixing .Of Plates To The Angle Of Rail Pole/Gi Pipes With Nuts And B Olts Will Be Done By The Contractors Note: All The Required Materials Including Iron Plates/Angles For Installation The Speakers To Be Supplied By The Contractors, As Per Annexure A Warranty Period: 30 Months After The Date Of Delivery Supply And Installation Pa Wall Speaker With Volume Control For Waiting Room, Enquiry Office As P Er Annexure A Warranty Period: 30 Months After The Date Of Delivery Supply, Installation Of Horn Type Speaker, Power 30 W Rms /45 W. & Fixing In The Shaded/Unshad Ed Area With Suitable Iron Plates For Hanging And Fixing Of The Speakers As Per Direction Of Rlys Engineer. Supply And Cutting Of Iron Plates, Fixing Of Plates To The Angle Of Raypole/Gi Pipes With Nuts And Bolts Will Be Done By The C Ontractors Note: All The Required Materials Including Iron Plates/Angles For Installation The Speakers To Be Supplied By The Contractors, As Per Annexure A Warranty Period: 30 Months After The Date Of Delivery
Replacement Of Corroded/Perforated Bracings, Gussets Plates, Cross Frames, Top Flange Angles & Other Members Including Replacement Of Loose Rivets Of Bridge No. 3204X30.5M, 391 1X18.3M, 4166X18.3M, 429A3x18.3M & 4841X12.2M, Br No.15Up & Dn2x12.2M, 16Dn1x12.2M, 22A3x12.2M, 23Dn 1X12.2M+1X9.15M, 32Up & Dn2x6x18.3M, 20512X18.3M And 2061X18.3M And Replacement Of Protection Sheet On Br. No. 24 Ner/Dn Line Under Jurisdiction Of Xen Bridge Line Lucknow. & Painting Of Steel Bridge Girders And Other Steel Structures, Including Miscellaneous Repair Work Of Bridges.
Rewiring Of Electrical Installation And Led Fittings At Te Bajaj Nagar - Point Wiring, 1 Or 2 Module 75Mmx75mm, 3 Module 100 Mmx75 Mm, 8 Module 125Mm X 125Mm, 12 Module 200Mmx150mm, Modular 5 Or 6 A Switch, Modular 15 Or 16 A Switch, 3 Pin 5 Or 6 A Socket Outlet, Modular 6 Pin 15 Or 16 A Socket Outlet, Modular Indicator, Modular Bell Push, Rj-45 One Module Cat 6 Computer Socket, 1 Run Of Utp 4 Pair Cat 6 Lan Cable, 2 Run Of Utp 4 Pair Cat 6 Lan Cable, 3 Run Of Utp 4 Pair Cat 6 Lan Cable, Medium Class Pvc Conduit, Two Module Fan Regulator, Modular Blanking Plate, 20 Mm Size Of Steel Conduit, 25 Mm Size Of Steel Conduit, 2 X 2.5 Sq Mm Plus 1 X 2.5 Sq Mm Earth Wire, 4 X 2.5 Sq. Mm Plus 2 X 2.5 Sq. Mm Earth Wire, 2X4 Sq. Mm Frls Pvc Insulated Copper Cable, 4X4 Sq. Mm Frls Pvc Insulated Copper Cable, Modular Gi Box Including Accessories, Frls Pvc Insulated Copper 3 X 1.5 Sq.Mm Wire, Frls Pvc Insulated Copper 6 X 1.5 Sq.Mm Wire, Frls Pvc Insulated Copper 3 X 2.5 Sq.Mm Wire, Frls Pvc Insulated Copper 6 X 2.5 Sq.Mm Wire, 20W Led T8 Tube, 20W Led Based Wall Mounting Pvc Batten, 1400 Mm Sweep Star Rated Energy Efficient Ceiling Fan, Itc Of Ceiling Fan, 18W Led Round Down Lighter, Fan Hook, 15Mm X 25Mm Sizes Pvc Slotted Channel, 25Mm X 25Mm Sizes Pvc Slotted Channel, Ding Dong Call Bell, Two Module Indicator, 5 A To 32 A Rating Single Pole Mcb, Shifting Of Office Material
Supply of Ferritic Steel Sheet 5X1250 X 3000 Mm., As Per Drawing: Rdso Spec No.C-K201, Gra De X2crni12 409M Table 1&2. Heat Treatment Condition 2D As Per Table-5., Packing Instructio N: Stainless Steel Sheets, Coils And Plates:- A Stainless Steel Austenitic & Ferritic S Teel Coils. The Coil Shall Be Protected In Reasonably Good Condition To Withstand Normal Handling Hazard During Transit With The Following Provision As The Barest Minimum: I Coil Should Be Wrapped With A Layer Of Water Proof Paper Through Out Whole Length. Ii Coil Should Be Wrapped With A Layer Of Biodegradeable Sheet. Iii O Uter & Inner Of Coil Should Be Wrapped With Gi Sheet. Iv Side Of The Coil Should Be C Overed With Card Board Sheet. V After This Whole Coil Should Be Wrapped With Biod Egradeable Plastic Sheet Of Suitable Thickness. Vi The Inner Edge Of The Coil Shoul D Be Protected By Gi Ring Followed By Another Iron Ring. Vii Outer Edge Of The Coil Should Be Wrapped With Gi Ring. Viii Coil Should Be Securely Strapped With Minium 5 Steel Bands Through The Eyes Of The Coil And Minium 3 Steel Bands On The Circumfer Ence Of The Eye. Ix Whole Coil Should Be Mounted On Wooden Blocks For Easy Liftin G/Stacking. X The Sheets In Coil Form For Thickness 2Mm And Above Shall Have: Inner Dia Of Coil 450-800Mm Outer Dia Of Coil 1000-1300Mm Weight Of Coil 2.4 - 10 Tonnes Xi The Sheets In Coil Form For Thickness Below 2Mm Shall Have: Inner Dia Of Coil 450-650Mm O Uter Dia Of Coil 1000-1300Mm Weight Of Coil 5.0 - 10 Tonnes. B Stainless Steel Austeniti C & Ferritic Steel Plates/Sheets I The Sheets/Plates Shall Be Supplied In Bundles Of Optimum Weight: 2Mt+/-10% & Each Sheet/Plate Shall Be Seprated With A Layer Of Wate R Proof Paper, After This The Whole Bundle Should Be Wrapped With Double Layer O F Water Proof Paper And A Biodegradeable Plastic Sheet Of Suitable Thickness. A Me Tal Protection In Edges Should Also Be Provided. Ii All Bundles Shall Have A Minimum Of 2 Hoops Upto 1.2 Meter In Length And One Extra Hoop For Every Additional Meter. The Bundles Shall Also Be Provided With Skid Wooden Packing Under Neath To Facili Tate Handling. Mechanical Damange & Corrosion During Transit If Any Shall Be At Th E Cost Of Supplier. Warranty Period: 30 Months After The Date Of Delivery Ferritic Steel Sheet 3X1250x3100 Mm., As Per Drawing: Rdso Spec. No. C-K201, Gra De X2crni12 409M Table 1&2, Heat Treatment Condition 2B As Per Table-5., Packing Instructi On: Stainless Steel Sheets, Coils And Plates:- A Stainless Steel Austenitic & Ferritic Steel Coils. The Coil Shall Be Protected In Reasonably Good Condition To Withstand Normal Handling Hazard During Transit With The Following Provision As The Barest Minimum: I Coil Should Be Wrapped With A Layer Of Water Proof Paper Through Out Whole Length. Ii Coil Should Be Wrapped With A Layer Of Biodegradeable Sheet. Iii O Uter & Inner Of Coil Should Be Wrapped With Gi Sheet. Iv Side Of The Coil Should Be C Overed With Card Board Sheet. V After This Whole Coil Should Be Wrapped With Biod Egradeable Plastic Sheet Of Suitable Thickness. Vi The Inner Edge Of The Coil Shoul D Be Protected By Gi Ring Followed By Another Iron Ring. Vii Outer Edge Of The Coil Should Be Wrapped With Gi Ring. Viii Coil Should Be Securely Strapped With Minium 5 Steel Bands Through The Eyes Of The Coil And Minium 3 Steel Bands On The Circumfer Ence Of The Eye. Ix Whole Coil Should Be Mounted On Wooden Blocks For Easy Liftin G/Stacking. X The Sheets In Coil Form For Thickness 2Mm And Above Shall Have: Inner Dia Of Coil 450-800Mm Outer Dia Of Coil 1000-1300Mm Weight Of Coil 2.4 - 10 Tonnes Xi The Sheets In Coil Form For Thickness Below 2Mm Shall Have: Inner Dia Of Coil 450-650Mm O Uter Dia Of Coil 1000-1300Mm Weight Of Coil 5.0 - 10 Tonnes. B Stainless Steel Austeniti C & Ferritic Steel Plates/Sheets I The Sheets/Plates Shall Be Supplied In Bundles Of Optimum Weight: 2Mt+/-10% & Each Sheet/Plate Shall Be Seprated With A Layer Of Wate R Proof Paper, After This The Whole Bundle Should Be Wrapped With Double Layer O F Water Proof Paper And A Biodegradeable Plastic Sheet Of Suitable Thickness. A Me Tal Protection In Edges Should Also Be Provided. Ii All Bundles Shall Have A Minimum Of 2 Hoops Upto 1.2 Meter In Length And One Extra Hoop For Every Additional Meter. The Bundles Shall Also Be Provided With Skid Wooden Packing Under Neath To Facili Tate Handling. Mechanical Damange & Corrosion During Transit If Any Shall Be At Th E Cost Of Supplier. Warranty Period: 30 Months After The Date Of Delivery Ferritic Steel Sheet 4X1250x3100 Mm., As Per Drawing: Rdso Spec. No. C-K201, Gra De X2crni12 409M Table 1&2, Heat Treatment Condition 2B As Per Table-5., Packing Instructi On: Stainless Steel Sheets, Coils And Plates:- A Stainless Steel Austenitic & Ferritic Steel Coils. The Coil Shall Be Protected In Reasonably Good Condition To Withstand Normal Handling Hazard During Transit With The Following Provision As The Barest Minimum: I Coil Should Be Wrapped With A Layer Of Water Proof Paper Through Out Whole Length. Ii Coil Should Be Wrapped With A Layer Of Biodegradeable Sheet. Iii O Uter & Inner Of Coil Should Be Wrapped With Gi Sheet. Iv Side Of The Coil Should Be C Overed With Card Board Sheet. V After This Whole Coil Should Be Wrapped With Biod Egradeable Plastic Sheet Of Suitable Thickness. Vi The Inner Edge Of The Coil Shoul D Be Protected By Gi Ring Followed By Another Iron Ring. Vii Outer Edge Of The Coil Should Be Wrapped With Gi Ring. Viii Coil Should Be Securely Strapped With Minium 5 Steel Bands Through The Eyes Of The Coil And Minium 3 Steel Bands On The Circumfer Ence Of The Eye. Ix Whole Coil Should Be Mounted On Wooden Blocks For Easy Liftin G/Stacking. X The Sheets In Coil Form For Thickness 2Mm And Above Shall Have: Inner Dia Of Coil 450-800Mm Outer Dia Of Coil 1000-1300Mm Weight Of Coil 2.4 - 10 Tonnes Xi The Sheets In Coil Form For Thickness Below 2Mm Shall Have: Inner Dia Of Coil 450-650Mm O Uter Dia Of Coil 1000-1300Mm Weight Of Coil 5.0 - 10 Tonnes. B Stainless Steel Austeniti C & Ferritic Steel Plates/Sheets I The Sheets/Plates Shall Be Supplied In Bundles Of Optimum Weight: 2Mt+/-10% & Each Sheet/Plate Shall Be Seprated With A Layer Of Wate R Proof Paper, After This The Whole Bundle Should Be Wrapped With Double Layer O F Water Proof Paper And A Biodegradeable Plastic Sheet Of Suitable Thickness. A Me Tal Protection In Edges Should Also Be Provided. Ii All Bundles Shall Have A Minimum Of 2 Hoops Upto 1.2 Meter In Length And One Extra Hoop For Every Additional Meter. The Bundles Shall Also Be Provided With Skid Wooden Packing Under Neath To Facili Tate Handling. Mechanical Damange & Corrosion During Transit If Any Shall Be At Th E Cost Of Supplier. Warranty Period: 30 Months After The Date Of Delivery
Supply of Ferritic Steel Coil 1.6X1250mm., As Per Drawing: Rdso Spec. No. C-K201, Grade X2c Rni12 409M Table 1&2, Heat Treatment Condition 2B As Per Table-5., Packing Instruction: Stai Nless Steel Sheets, Coils And Plates:- A Stainless Steel Austenitic & Ferritic Steel Coils. The Coil Shall Be Protected In Reasonably Good Condition To Withstand Norm Al Handling Hazard During Transit With The Following Provision As The Barest Minim Um: I Coil Should Be Wrapped With A Layer Of Water Proof Paper Through Out Whole Length. Ii Coil Should Be Wrapped With A Layer Of Biodegradeable Sheet. Iii Outer & I Nner Of Coil Should Be Wrapped With Gi Sheet. Iv Side Of The Coil Should Be Covered With Card Board Sheet. V After This Whole Coil Should Be Wrapped With Biodegrade Able Plastic Sheet Of Suitable Thickness. Vi The Inner Edge Of The Coil Should Be Pr Otected By Gi Ring Followed By Another Iron Ring. Vii Outer Edge Of The Coil Should Be Wrapped With Gi Ring. Viii Coil Should Be Securely Strapped With Minium 5 Steel Ba Nds Through The Eyes Of The Coil And Minium 3 Steel Bands On The Circumference Of The Eye. Ix Whole Coil Should Be Mounted On Wooden Blocks For Easy Lifting/Stacki Ng. X The Sheets In Coil Form For Thickness 2Mm And Above Shall Have: Inner Dia Of C Oil 450-800Mm Outer Dia Of Coil 1000-1300Mm Weight Of Coil 2.4 - 10 Tonnes Xi The Sheets I N Coil Form For Thickness Below 2Mm Shall Have: Inner Dia Of Coil 450-650Mm Outer Di A Of Coil 1000-1300Mm Weight Of Coil 5.0 - 10 Tonnes. B Stainless Steel Austenitic & Fer Ritic Steel Plates/Sheets I The Sheets/Plates Shall Be Supplied In Bundles Of Optimu M Weight: 2Mt+/-10% & Each Sheet/Plate Shall Be Seprated With A Layer Of Water Proo F Paper, After This The Whole Bundle Should Be Wrapped With Double Layer Of Water Proof Paper And A Biodegradeable Plastic Sheet Of Suitable Thickness. A Metal Prot Ection In Edges Should Also Be Provided. Ii All Bundles Shall Have A Minimum Of 2 Ho Ops Upto 1.2 Meter In Length And One Extra Hoop For Every Additional Meter. The Bu Ndles Shall Also Be Provided With Skid Wooden Packing Under Neath To Facilitate H Andling. Mechanical Damange & Corrosion During Transit If Any Shall Be At The Cost Of Supplier. Warranty Period: 30 Months After The Date Of Delivery
Supply of Steel Sheet Of Size 15X2500x6400mm., As Per Drawing: Din En 10025-5 S355 J2w+N. Sp Ecification For Ultrasonic Testing Of Steel Plates Shall Be Astm-A-578Reapproved 20 01. The Acceptance Standard Shall Be Level B Para 8 Of Astm-A-578 With Frequency 100% All The Plates Shall Be Ut Testing, Scanning Shall Be Continuous Over 100% Of P Late Surface., Packing Instruction: Mild / Corten/ En Steel Coils, Sheets And Plates:- A Mil D, En And Corten Steel Sheets In Coil Form. The Coil Shall Be Protected In Reasonabl Y Good Condition To Withstand Normal Handling Hazard During Transit With The Fol Lowing Provision As The Barest Minimum: I The Whole Coil Should Be Wrapped With Do Uble Layer Of Water Proof Paper And A Biodegradeable Plastic Sheet Of Suitable Thi Ckness. Ii The Inner Edge Of The Coil Should Be Protected By Gi Ring Followed By An Other Iron Ring. Iii Outer Edge Of The Coil Should Be Wrapped With Gi Ring. Iv Coil Sh Ould Be Securely Strapped With Minium 5 Steel Bands Through The Eyes Of The Coil A Nd Minium 3 Steel Bands On The Circumference Of The Eye. V Hot Rolled Coils Shall B E Supplied With Rust Preventive Oil Coating On The Outer Layer, Inner Layer And On T He Both Edges. Vi Coils Processed Through Pickling And Or Skin Passing Or Cold Ro Lling Of Thickness Upto 2Mm Shall Be Protected Against Corrosion And Rust By Coat Ing Corrosion Preventive Fluid, Soft Film, Solvent Deposited, Waterdisplacing To Is: 1154 . Vii Whole Coil Should Be Mounted On Wooden Blocks For Easy Lifting/ Stacking. Viii The Sheets In Coil Form For Thickness 2Mm And Above Shall Have: Inner Dia Of Coil 450-800Mm Outer Dia Of Coil 1000-1300Mm Weight Of Coil 2.4 - 10 Tonnes Ix The Sheets In C Oil Form For Thickness Below 2Mm Shall Have: Inner Dia Of Coil 450-650Mm Outer Dia Of Coil 1000-1300Mm Weight Of Coil 5.0 - 10 Tonnes. B Mild, En And Corten Steel Plates/She Ets. I Plates Above 5Mm Shall Be Supplied With Reasonable Packing With Metal Strapi Ng For Handling During Transit And Storage. Ii The Sheets/Plates Shall Be Supplied I N Bundles With Double Layer Of Water Proof Paper & A Biodegradeable Plastic Shee T Of Suitable Thickness And Metal Protection In Edges.All The Sheets Upto 2Mm Thck Ness Shall Be Protected Against Corrosion And Rust By Coating Corrosion Prevent Ive Fluid, Soft Film, Solvent Deposited, Waterdisplacing To Is: 1154 And All The Sheets/ Plates Above 2Mm Shall Be Protected Against Corosion & Rust With Suitable Mineral Oil Or Other Temporary Rust Preventive Coating. Iii All Bundles Shall Have A Minimu M Of 2 Hoops Upto 1.2 Meter In Length And One Extra Hoop For Every Additional Mete R. The Bundles Shall Also Be Provided With Skid Wooden Packing Under Neath To Fa Cilitate Handling. Iv Optimum Weight Of The Bundle Should Be 2Mt+-10%. Mechanical D Amange & Corrosion During Transit If Any Shall Be At The Cost Of Supplier. Warranty Period: 30 Months After The Date Of Delivery Steel Sheet Of Size 8X2500x4500mm., As Per Drawing: Din En 10025-5 S355j2w+N.Spe Cification For Ultrasonic Testing Of Steel Plates Shall Be Astm-A-578Reapproved 200 1. The Acceptance Standard Shall Be Level B Para 8 Of Astm-A-578 With Frequency 1 00% All The Plates Shall Be Ut Testing, Scnanning Shall Be Continuous Over 100% Of Plate Surface., Packing Instruction: Mild / Corten/ En Steel Coils, Sheets And Plates:- A Mi Ld, En And Corten Steel Sheets In Coil Form. The Coil Shall Be Protected In Reasonab Ly Good Condition To Withstand Normal Handling Hazard During Transit With The Fo Llowing Provision As The Barest Minimum: I The Whole Coil Should Be Wrapped With D Ouble Layer Of Water Proof Paper And A Biodegradeable Plastic Sheet Of Suitable T Hickness. Ii The Inner Edge Of The Coil Should Be Protected By Gi Ring Followed By A Nother Iron Ring. Iii Outer Edge Of The Coil Should Be Wrapped With Gi Ring. Iv Coil S Hould Be Securely Strapped With Minium 5 Steel Bands Through The Eyes Of The Coil And Minium 3 Steel Bands On The Circumference Of The Eye. V Hot Rolled Coils Shall Be Supplied With Rust Preventive Oil Coating On The Outer Layer, Inner Layer And On The Both Edges. Vi Coils Processed Through Pickling And Or Skin Passing Or Cold R Olling Of Thickness Upto 2Mm Shall Be Protected Against Corrosion And Rust By Co Ating Corrosion Preventive Fluid, Soft Film, Solvent Deposited, Waterdisplacing To I S: 1154 . Vii Whole Coil Should Be Mounted On Wooden Blocks For Easy Lifting/ Stacki Ng. Viii The Sheets In Coil Form For Thickness 2Mm And Above Shall Have: Inner Dia Of Coil 450-800Mm Outer Dia Of Coil 1000-1300Mm Weight Of Coil 2.4 - 10 Tonnes Ix The Sheet S In Coil Form For Thickness Below 2Mm Shall Have: Inner Dia Of Coil 450-650Mm Outer Dia Of Coil 1000-1300Mm Weight Of Coil 5.0 - 10 Tonnes. B Mild, En And Corten Steel Plat Es/Sheets. I Plates Above 5Mm Shall Be Supplied With Reasonable Packing With Metal Straping For Handling During Transit And Storage. Ii The Sheets/Plates Shall Be Sup Plied In Bundles With Double Layer Of Water Proof Paper & A Biodegradeable Plastic Sheet Of Suitable Thickness And Metal Protection In Edges.All The Sheets Upto 2Mm Thckness Shall Be Protected Against Corrosion And Rust By Coating Corrosion Pre Ventive Fluid, Soft Film, Solvent Deposited, Waterdisplacing To Is: 1154 And All The Sh Eets/Plates Above 2Mm Shall Be Protected Against Corosion & Rust With Suitable Min Eral Oil Or Other Temporary Rust Preventive Coating. Iii All Bundles Shall Have A Mi Nimum Of 2 Hoops Upto 1.2 Meter In Length And One Extra Hoop For Every Additional Meter. The Bundles Shall Also Be Provided With Skid Wooden Packing Under Neath T O Facilitate Handling. Iv Optimum Weight Of The Bundle Should Be 2Mt+-10%. Mechanic Al Damange & Corrosion During Transit If Any Shall Be At The Cost Of Supplier. Warr Anty Period: 30 Months After The Date Of Delivery
Supply At Site, Testing Of 5Mtr. Polygonal/Octagonal Gi Lighting Mast /Pole With Double Arm Provisio N For Lighting Purpose, As Per Dimension Top Dia - 70Mm, Bottom Dia- 130Mm, Thickness-4Mm, Base Plate-220X 220X12 Mm, Pcd-220Mm, Foundation Bolt- M16x 600X4, All Material Should Be Of Is Tolerance With All Necessa Ry Accessories To Complete The Work In All Respect. Cost Includes Cost Of Power Supply Arrangement Including Wiri Ng And Necessary Reliable Protective Device If Required As Per Site Requirement As Advised By Railway Site Inchar Ge. Warranty Period: 30 Months After The Date Of Delivery
Outdoor Fitting Led Light, Supply And Fixing Of Energy Efficient Geyser, Supply And Fixing Of Led Recess Mounted Light, Supply And Fixing Of Chandelier Light, Supply And Fixing Of 2 To 5 Watt Led Based Modular Type Reading Lamp Fitting, Supply Of Bracket Fan 400 Mm Sweep, Supply And Fixing Of 1200 Mm Sweep Ceiling Fan, Supply And Fixing Of Led Decorative Garden Bollard Light 6-7 Watt, Supply And Fixing Of 12 Module Gi Box With Covering Plate, Supply And Fixing Of Bracket Fan 400 Mm Sweep, Supply And Fixing Of Exhaust Fan 300 Mm Sweep, Supply And Fixing Of 1200 Mm Sweep Decorative Type Ceiling Fan, Supply And Fixing Of Led Indoor Fitting 18-20 Watt, Supply And Fixing Of Led Outdoor Fitting 30 Watt, Supply And Fixing Of Energy Efficient Geyser 15 Ltrs Capacity, Supply And Fixing Of Led Bulb 7-9 Watt, Supply And Fixing Of Led Fitting 18-20 Watt, Supply And Fixing Of Led Outdoor Street Light 25 Watt, Battery
Supply of 63 Transformer Vcb Rubber Matting Standard Shock Treatment Charts In English And Hindi Providing And Fixing Ht Danger Notice Plate Of 250 Mm Into 200 Mm Made Of Mild Steel At Least 2 Mm Thick As Per Atc Supplying And Fixing Of Gi Fire Buckets With Round Bottom Each Set Comprising 3 Nos Buckets As Per Atc Ms Angle Iron And Ms Flate And Ms Wire Mesh As Per Atc
Supply Of Ement 43 Grade Opc Packed In Hope Bag Each 50Kg Wt Conform To Is 8112 And1989, Coarse Sand Free From Vegetation, Coarse Aggregate 20Mm Graded, Coarse Aggregate 40Mm Graded, Coarse Aggregate 40Mm To 63Mm Graded, Ms Angle 40 X 40 X 6Mm For Cleat, Ms Rhs 80 X 40 X 3.2Mm, Ms Rhs 50 X 25 X 2.9Mm, Ms Rhs Of 96 X 48 X 3.2Mm, Ms Plate 8Mm Thick, Ms Nut And Bolts Of Lenth 100Mm Thred Suitable For 10Mm Dia Nuts, Ms Fkate 40 X 5Mm For Wind Tie Make Tata Sail Jsw, Iron Welding Rod Conforming To Is 814 2002 3.15Mm Thick 100Nos, Self Taping Steel Screw Thread With Rawl Plug 1.5 Inch, Pre Painted Galvatume Aluminum Zinc Coating Gi Based Plain Steel Sheet 0.50Mm
Supply Of Calculater 12Digit, A4 Size Paper, Envelope 9 X 4 Per Pcs, Envelope 11 X 5 Per Pcs, Highlighter, Whitener, Office Bag, File Bag, Stapler Big, Ink Pad, Paper Pin T Type, Ball Pen, File Cover, Old Dhoti, Duster Cloth, Handwash 200Ml, Soap, Marker Ink, Pencil, Eraser, Sharpner, Ddr 4 Ram, Drawing Paper, Drawing Sheet, Water Cooler Motor For Selfie Point, C Pvc Pipe 1Inch, C Pvc Pipe 2Inch, Pvc Tape, Sumercibale Motor 3Hp 1Phase, Stater L And T, Phenyl Liquied Per Ltr, Chinees Pin Per Pkt, Plastic Gulli Per Pkt, Kaju Pin 2.5Mm Per Pkt, Condensor 2.5Mfd, Copper Wire 2.5Mm Per Coil 90Mtr, Copper Wire 1.5Mm Per Coil 90Mtr, Copper Wire 0.75Mm Per Coil 90Mtr, Bathroom Toti Gi, Jhaler Copper Wire Per Mtr, Capaciter 200 To 25 Mfd, Pvc Wire 1-15Mm Almiunium Per Coil, Pvc Wire 1-18Mm Alminium Per Coil, Pvc Wire 3-22Mm Almunium Per Coil, Pvc Wire 7-22Mm Almunium Per Coil, Heater Coil 2000Kw, Heater Plate 15Cm, Led 9W, Led 15W, Bulb 100W, 3Pin Plug 6A 250V, Cotton Tape, Pvc Casing Caping T L Joint, Hexa Blade Per Pkt 100Pcs, Chalk Per Pkt, Welding Electrode 2.5Mm 12 No Per Pkt, Ms Iron Sheet, Ag4 Grinder Blade, Ms Plate 50 X 10 Per Kg, First And Box, Plastic Bucket, Plastic Mug, Padlock 65Mm, Milton Cloth 6 X 4, Steal Scale, Tub Water