Supply Of 60T Capacity Double Girder Eot Crane With 25M Lift Of Main Hook, Nine Point One Meter Span Bfp Area Crane - Refer Unpriced Boq In Gem Atc And Technical Specification Pe-Ts- 504-501-A002, Dsl For 64 M Bay Length - Refer Un-Priced Boq In Gem Atc And Technical Specification Pe-Ts-504-501- A002, 64 M Bay Length Gantry Rail- Refer Un-Priced Boq In Gem Atc And Technical Specification Pe-Ts-504-501-A002, Set Of Axle Bearings - Refer Un-Priced Boq In Gem Atc And Technical Specification Pe-Ts-504-501-A002, Set Of Gearbox Bearings With Sleeves - Refer Un-Priced Boq In Gem Atc And Technical Specification Pe-Ts-504-501-A002, Long Travel End Shaft Bearings - Refer Un-Priced Boq In Gem Atc And Technical Specification Pe-Ts-504-501-A002, Coupling - Refer Un-Priced Boq In Gem Atc And Technical Specification Pe-Ts-504-501-A002, Seals For Travel Gear Box - Refer Unpriced Boq In Gem Atc And Technical Specification Pe-Ts- 504-501-A002, Long Travel Brake Shoes Lining- Refer Unpriced Boq In Gem Atc And Technical Specification Pe-Ts- 504-501-A002, Axle Bearings - Refer Un-Priced Boq In Gem Atc And Technical Specification Pe-Ts-504-501-A002, Set Of Seals For Gearbox - Refer Un-Priced Boq In Gem Atc And Technical Specification Pe-Ts-504-501-A002, Cross Travel End Shaft Bearing - Refer Un-Priced Boq In Gem Atc And Technical Specification Pe-Ts-504-501-A002, Cross Travel Brake Shoes Lining - Refer Un-Priced Boq In Gem Atc And Technical Specification Pe-Ts-504-501-A002, Main Hoist Pulley Bearings - Refer Un-Priced Boq In Gem Atc And Technical Specification Pe-Ts-504-501-A002, Set Of Bearings For Gear Box - Refer Un-Priced Boq In Gem Atc And Technical Specification Pe-Ts-504-501-A002, Set Of Seals For Main Hoist - Refer Un-Priced Boq In Gem Atc And Technical Specification Pe-Ts-504-501-A002, Main Hoist Brake Shoes - Refer Un-Priced Boq In Gem Atc And Technical Specification Pe-Ts-504-501-A002, Main Hoist Brake Springs - Refer Unpriced Boq In Gem Atc And Technical Specification Pe-Ts- 504-501-A002, Main Hoist Brake Shoe Liners - Refer Unpriced Boq In Gem Atc And Technical Specification Pe-Ts- 504-501-A002, Bearings De And Nde For Each Type And Rating Of Motors - Refer Un-Priced Boq In Gem Atc And Technical Specification Pe-Ts-504-501-A002, Motor Of Each Type And Rating - Refer Un-Priced Boq In Gem Atc And Technical Specification Pe-Ts-504-501-A002, Site Visits - Refer Un-Priced Boq In Gem Atc And Technical Specification Pe-Ts-504-501-A002, Supervision Of Erection And Commissining - Refer Un-Priced Boq In Gem Atc And Technical Specification Pe-Ts-504-501-A002
Supply Of Ci Cs Casted Items -C.I. Idler For Cane Carrier I As Per Drawing No. Ksc/Cc1/4/17, , C.I. Pulley As Per Drawing With Machining, C.I. Coupling Different Size As Per Drawing, C.I. Casting Various Size Gulla As Per Drawing With Rough Machining. Different Size, , Cast Steel Spur Gear & Pinion New Basis, Cast Steel & Spur Gear- 72 Teeth, Face Width- 75Mm, Bore- 50Mm Od- 473 Mm, Module- 6.4. Approx Weight 90 Kg, , Cast Steel & Spur Gear- 26 Teeth, Face Width- 75Mm, Bore- 45Mm Od- 178.24 Mm, Module- 6.4- Approx Weight 11.6 Kg, , Cast Steel Pinion- 24 Teeth, Face Width- 70Mm, Bore- 45Mm Od- 166.4 Mm, Module- 6.4 -Approx Weight 9.7 Kg, , Cast Steel Pinion- 34 Teeth, Face Width- 75Mm, Bore- 40Mm Od- 308 Mm, Module- 8.56. Approx Weight 20 Kg, , Cast Steel Gear Pinion- 50 Teeth, As Per Drg No. Mills-138Approx Weight 11 Kg, , Cast Steel Sprocket- 13 Teeth 6” Pitch, As Per Drg. Mills-27, , Cast Steel Pinion- 18 Teeth, Face Width- 75Mm, Bore- 45Mm Od- 128 Mm, Module- 6.4.Approx Weight 5 Kg, , C.S.Scaper For Mills Duly Machined As Per Sample Drg.No Ksc/Mh/91618 Approx Wt-190Kg Each, Cast Steel Trash Plate Lenth 1680 Mm Made Of Is 2708 Grade Iii Duly Rough Machined As Per Drg.No – Ksc/Mh/285/22, C.S. Wheel For Cane Unloader Bridge As Per Drg.No. Ksc/Unloader/2/17.Approx Wt 185 Kg., C.S Gear 68 Teeth, Module-6.14, Face Width-65Mm, O.D--430Mm, Drg No.-Ksc/Unloder/17, C.S.Wheel For Cane Unloder Trolly Drg No.-Ksc/Cr/145 Approx.Wight-55Kg, C.S.Pinion-18Teeth, Module-6.14, F.W-65 Od-122.8 Drg. No.-Ksc/Unloder/17, C.S. Sprroket 6 Pich 14 Teeth Drg No.-Ksc/M/1565 Tail End Material 2708, C.S. Sprroket 6 Pich 14 Teeth Drg No.-Ksc/M/1564 Driving Shaft Material 2708, C.S.Sproket-36 Teeth For Duplex Chain 2 1/2 Pitch Material 2708 Drg No Ksc/Boiler-163, C.S. Sprocket 17 Teeth For Duplex Chain 2 1/2 Pitch Material 2708 Drg No-Ksc/Mill/4887, Opertuinity Device Of Trash Turner Beam Material-Ss Drg No. Mills-8488, C.S. Pinion Duly Hardent Tempered And Grinded- 24 Teeth, Module-10, Fw-110Mm Od-260Mm Bore-50Mm, C.S. Pinion Duly Hardent Tempered And Grinded- 24 Teeth, Module-8, Fw-120Mm Od-208 Mm Bore-50Mm, C.S.Worm Shaft As Per Sample For Mill, C.S. Mill Coupling Weight 700Kg Approx As Per Drawing, C.S. Mill Crown Pinion 16 Teeth Weight 1500 Kg. As Per Drawing, Cast Steel Spur Gear & Pinion On Conversion Basis, Cast Steel & Spur Gear- 72 Teeth, Face Width- 75Mm, Bore- 50Mm Od- 473 Mm, Module- 6.4. Approx Weight 90 Kg, , Cast Steel & Spur Gear- 26 Teeth, Face Width- 75Mm, Bore- 45Mm Od- 178.24 Mm, Module- 6.4- Approx Weight 11.6 Kg, , Cast Steel Pinion- 24 Teeth, Face Width- 70Mm, Bore- 45Mm Od- 166.4 Mm, Module- 6.4 -Approx Weight 9.7 Kg, , Cast Steel Pinion- 34 Teeth, Face Width- 75Mm, Bore- 40Mm Od- 308 Mm, Module- 8.56. Approx Weight 20 Kg, , Cast Steel Gear Pinion- 50 Teeth, As Per Drg No. Mills-138Approx Weight 11 Kg, , Cast Steel Sprocket- 13 Teeth 6” Pitch, As Per Drg. Mills-27, , Cast Steel Pinion- 18 Teeth, Face Width- 75Mm, Bore- 45Mm Od- 128 Mm, Module- 6.4.Approx Weight 5 Kg, , C.S.Scaper For Mills Duly Machined As Per Sample Drg.No Ksc/Mh/91618 Approx Wt-190Kg Each, Cast Steel Trash Plate Lenth 1680 Mm Made Of Is 2708 Grade Iii Duly Rough Machined As Per Drg.No – Ksc/Mh/285/22, C.S. Wheel For Cane Unloader Bridge As Per Drg.No. Ksc/Unloader/2/17.Approx Wt 185 Kg., C.S Gear 68 Teeth, Module-6.14, Face Width-65Mm, O.D--430Mm, Drg No.-Ksc/Unloder/17, C.S.Wheel For Cane Unloder Trolly Drg No.-Ksc/Cr/145 Approx.Wight-55Kg, C.S.Pinion-18Teeth, Module-6.14, F.W-65 Od-122.8 Drg. No.-Ksc/Unloder/17, C.S. Sprroket 6 Pich 14 Teeth Drg No.-Ksc/M/1565 Tail End Material 2708, C.S. Sprroket 6 Pich 14 Teeth Drg No.-Ksc/M/1564 Driving Shaft Material 2708, C.S.Sproket-36 Teeth For Duplex Chain 2 1/2 Pitch Material 2708 Drg No Ksc/Boiler-163, C.S. Sprocket 17 Teeth For Duplex Chain 2 1/2 Pitch Material 2708 Drg No-Ksc/Mill/4887, Opertuinity Device Of Trash Turner Beam Material-Ss Drg No. Mills-8488, C.S. Pinion Duly Hardent Tempered And Grinded- 24 Teeth, Module-10, Fw-110Mm Od-260Mm Bore-50Mm, C.S. Pinion Duly Hardent Tempered And Grinded- 24 Teeth, Module-8, Fw-120Mm Od- 208 Mm Bore-50Mm, C.S.Worm Shaft As Per Sample For Mill, C.S. Mill Coupling Weight 700Kg Approx, C.S. Mill Crown Pinion 16 Teeth Weight 1500 Kg.
Supply Of Nut For Cap,, Gasket, Sleeve, Bearing Ball 6205, Seal Ring, O Ring For Bushing, Bushing, Washer For Feed Pump, Shear-Pin Coupling, Inch O Inch Ring Rub3034-71, Dia 4.35X39.7Dn 260124/14238, Washer Intermediate, O Ring Rub3034-71Dia6.3X124.7Artno69270drg260124, Screw Spanner, Ball Bearing, Seal Ring 2390, O Ring, Control Paring Disc, Seal Ring, Bolt, Screw Screw, O Ring, Pin, Snap Ring, Seal Ring, Oil Paper Packing, Screw, Seal Ring, Lock Gravity Ring Mab 103/300, Interactive Washer, Spanner For Oil Drain, Packing, Screw, Gange Glass, Gasket, O Ring,, O Ring, Bushing, Packing, Gravity Disk, Impeller,, Impeller, Screen, Top Bearing, Nut, Gasket, Ball Bearing 6202, Pin, Stud Bolt, Packing, Ball Bearing, Seal Ring, Packing End Shield, Tooth Rim For Flexible Coupling, Spring, Seal Ring, Gauge Glass Oil, Set Of Spares Of O Ring & Gasket Diapharam Kit, Valve Cone For Mab205, Lock Washer, Worm Wheel, Socket 9/16Inch 1/2Inch, Bushing, Pipe Inlet, Packing, Packing, Worm, Ring Wear, Round Nut Skf Km5, Seal Ring, O Ring, O Ring, Seal Ring, Ring Joint Rulen Gasket, Fixing Plate, Nut For Feed Tube, Spring, Handle, Spanner Socket, Deflector, Bearing Housing, 3-Way Solenoid Valve Normally Closed Conn 1/4 Npt, Socket For Socket Spanner, Glass Level, Screw Lock, Seal Ring, O Ring, Gasket, Pin Taper, Ring Rubber Large For Separator Bowl, Gasket, O-Ring, Plate Elastic, O Ring, Valve Solenoid, Impeller, Gasket, O Ring, Rivet, Friction Pad, Pin, Bowl Spindle, Packing, Bowl Disc, Worm Wheel With Pin, Spring, Buffer, O Ring, O Ring, Seal Ring, Frame Foot, Fan, Labyrinth Ring Holder, Spindle Pulley
Procurement Of Miscelleneous Items, Grinding Wheel For -Hitachi, Disc Grinder Model Pda 100D Size 100X4x16 Mm Spec-A 24R, Compound Holdtite Perfoct, Hitachi Portable Angle Grinder Model Pqa-100D With Cutting Attachment 230V, 620W, 12000Rpm Size 100Mm, Holder For Welding Electrode 600Amp Confirming To Relivent Is- No, Coupling Pump Complete Hrc-130, Hoist Ratchet Chain Type 1.5Ton, Adjustable Wrench -Screw Wrench, Made Of Carbon Steel Standard Pattern. Burnshed Handle With Ground H.D. As Per Relivent Is No 6149-1971 12-Inch, White Metal Lead Base - 75Percent Lead, 15Percent Antimony And 10Percent Tin, Coupling Flexible Fenner-B-6, Air Operated Grease Gun Barrel Type 200 Ltrs Capacity With 7.5 Metre Long Grease Hose, L And Z Swivel And Other Standard Accessories, High Speed Steel Hack Saw Blade As Per Is-No 1By2-Inch X 12-Inch -14Tp, 23Gauge, High Speed Steel Power Hack Saw Blade As Per Isno 1.1By4-Inch X 17-Inch, Chain Pulley Block 3.Ton - 20Mtr, Geared Travelling Trolly 3.0Ton -5.0Mtr, Belt Fastners 2-Inch X 7By32-Inch, Insert For Male Coupling, Wire Rope Ungalvanised Steel, Dia-16Mm, Construction- 6X37, Steel Core, Tensile Designation Of Wire -1770N Per Mm2, 180Kgfpermm2, Minimum Breaking Strength -144Kn, As Per Is-2266-2002, Latest Version, Wire Rope Ungalvanised Steel, Dia1by2-Inch, Construction-6X19, Steel Core, Tensile Designation Of Wire-1770Npermm2, 180Kgfpermm2, Rope Dia-12.7Mm, Minimum Breaking Strength-95Kn, As Per Is-2266-2002
