Chemical Scrap Tenders

(Select any tender from the list to send an email)
Ref. No #31941783 Central Government/Public Sector Live

Supply of Solution For Derusting And Cold Zinc Phosphating.Icf Specification For Cold Zinc Phosphatingsolution.Icf/Md Spec.115.---------------------------------------------------- -I.A The Solution Should Be Clear And Free From Insolubleimpurities.B Specific Gravity Of The Solution Should Be 1.18Min.C Solution Should Freely Miscible With Distilled Water.Ii When Mixed 1 Part Of The Solution With 2 Parts Of Distilledwater The Resultant Solution Should Meet The Followingrequirements.A The Solution Should Be Able To Remove The Mild Rust Grade Aofiso 8501-1;1988 D & Oil Or Grease Adhering To Steel Sheets.B Solution Should Form A Crystalline Zinc Phosphate Coatingon Application By Brush Or By Dipping On Steel Sheets.Iii When A Thoroughly Cleaned M.S. Test Panel Of Size 10X5 Cmis Immersed In1:2 Solution 1 Part Of Zinc Phosphate Solution+2 Parts Of Distilled Water For A Period Of 10 Minutes Thezinc Phosphate Coating Formed Should Meet The Followingrequirements. A Coating Factor - Class `C Of Is 3618/19661.1 -4.3 Gm/M2b Scrap A Small Area - The Phosphated Surface Shouldof The Test Panel With A Yield A Powder.Sharp Blade.C Scrap Asmall Area - The Phosphated Surface Shouldthe Test Panel With A Show A Whitish Streak.Blunt Knife.D Qualitative Test For - The Coating Removed From Thezinc& Phosphate. Test Panel Should Answer Thetest Forzinc Phosphate.Iv On Handling Of The Solution It Should Not Cause Any Injury Orirritation To The Skin Of Worker.******************. Solution For Derusting And Cold Zinc Phosphating.Icf Specification For Cold Zinc Phosp Hatingsolution.Icf/Md/Spec.115.-----------------------------------------------------I.A The Solution Should Be Cle Ar And Free From Insolubleimpurities.B Specific Gravity Of The Solution Should Be 1.18Min.C Solution Should Fre Ely Miscible With Distilled Water.Ii When Mixed 1 Part Of The Solution With 2 Parts Of Distilledwater The Resultant Solu Tion Should Meet The Followingrequirements.A The Solution Should Be Able To Remove The Mild Rust Grade Aofiso 8501-1;1988 D & Oil Or Grease Adhering To Steel Sheets.B Solution Should Form A Crystalline Zinc Phosphate Co Atingon Application By Brush Or By Dipping On Steel Sheets.Iii When A Thoroughly Cleaned M.S. Test Panel Of Size 10X5 Cmis Immersed In1:2 Solution 1 Part Of Zinc Phosphate Solution+2 Parts Of Distilled Water For A Period Of 10 Minutes Thezinc Phosphate Coating Formed Should Meet The Followingrequirements.A Coating Factor - Class `C Of Is 3618/19661.1 -4.3 Gm/M2b Scrap A Small Area - The Phosphated Surface Shouldof The Test Panel With A Y Ield A Powder.Sharp Blade.C Scrap Asmall Area - The Phosphated Surface Shouldthe Test Panel With A Show A Wh Itish Streak.Blunt Knife.D Qualitative Test For - The Coating Removed From Thezinc& Phosphate. Test Panel Should A Nswer Thetest Forzinc Phosphate.Iv On Handling Of The Solution It Should Not Cause Any Injury Orirritation To The Ski N Of Worker.******************

Location
Tamil Nadu
Due Date
08 Jul, 2024
Amount
Refer Document
Ref. No #31931506 State Government Live

Supply Of Allied Material And Tand P Items LT Bush Rods (M-12),LT Bush Rods (M-20),"LT Bush Rods (M-30) ,L.V. Bush Rods M-30/M-40 ",HT Bush Rods (11 Kv),LV Bushings (12mm),LV Bushings (20mm),"LV Bushings (32/30 mm) ,",HT Bushing (11 Kv),Film Paper,Lethoride Paper/Khakhi Paper,Press Boards,Gutties,Rubber Washer of Different Sizes,HT Washers,LT Washers M-12,LT Washers M-20,LT Washers M-30/M-40,Cork Sheets (1000mmx500mmx5mm),Rubberized Cork strip(40mmx5mm),Bakelite Tubes,Cotton Tape,Nawar Tape,M.Seal,Glass Sleeves,Insulation Gum,Wooden Wedges,Craft Paper,Packing Sheets,Aluminum Gutka,Nuts & Bolts,H.T. Bush Clamps,Copper Brazing Rod,Aluminum Brazing Rod,H.T / L.T Oil Seals-12,H.T / L.T Oil Seals-20,H.T / L.T Oil Seals-30/40,Cotton Waste (Old Cotton Sarres/Cloth),M.S Washers for L.T Connections ,Plugs of different sizes ¾” 1¼” 1” ½” ,Flux,Grey Paint,Turpentine oil ,Varnish ,Welding Rods (8mm & 10mm),Oven Heating/Elements Coils,3½ Multi Stands Cu Cable (10 mm ) ,Thinner,Crepe Tape,Oxygen Cylinder (Refill),Megger (500Volt, 5000 MW),Oxygen Regulator,Oxygen Cylinder Nozzle ,Oxygen Pipe for Gas Cutter,Clamp for Oxygen Pipe,C Clamp 18”,Hydraulic Transformer Lifting Trolley,Trolley for Scrap Loading/Unloading ,Clamp Meter,Welding Helmet,Welding Cable with Holder ,Cutter Pliers ,Screw Driver (all sorts) ,Ratchet Wrench with Socket Set compete,Pipe Wrench 12”,Pipe Wrench 18”,Bolt Cutter 12”,Bolt Cutter 18”,Spanner 15/21 MM ,Spanner 38/48 MM ,Oven Thermostat (0-300 Amp),Contractor 63 Amp ISI ,10KA of Reputed make,Cable Wire 16 mm.,Filter Plant High Pressure supply Hose 25 MM (1”), 35 bar/500 PSI ,Filter Tank Pipe Rubber,Wooden Frames for Winding of HT /LT,Exhaust Fans for Workshop 24”Heavy Duties,Pedestal Fans for Workshop (Heavy Duty),Out Side Clipper for Winding Machines ,Inside Clipper for Winding Machines ,Heavy Duty Drill Machine (1050 Watt),Scissors (large size for cutting papers),Test Cell of oil Testing Machine (60KV) (500 ML/ Acrylic Test Cell) with removable & adjustable electrodes ,HT/LT Winding Machines Bearing ,HT/LT Winding Machines Bearing VEE-Belts,HT/LT Winding Machines Bearing Gear-Box,HT/LT Winding Machines Bearing Foot-Switch,HT/LT Winding Machines Bearing Counters,1 HP Pump Motor Centrifugal ,Change Over Switch 400 Amp,MCCB 4 Pole 100 Amp(25KA),Scale Steel 1 meter,Scale Steel 12 Inch,EOT Crane Switch ,Angle Grinder (850 Watts),Air Blower Macine (900 Watts),Digital Micrometer 0 to 25 mm,LPG 19 Kg (Refill) ,Laminated Core of all Sorts,Multi Stand 3 Core Copper Cable 10 sqmm,Testing Clips,Saw Dust,Dust Sand

Location
Jammu And Kashmir
Due Date
02 Jul, 2024
Amount
Refer Document