Technical Support

Technical Support for tender Earthwork In Excavation Of Foundation In Hard Soil Including Dressing & Levelling Of Bed Within Initial Lead Of 50mt. & Lift Of 1.5mtr Etc Complete As Per The Direction Of The Engineer-incharge. Filling In Foundation & Plinth With Sand Including Watering & Ramming Etc Complete As Per The Direction Of The Engineer-incharge. Cement Concrete (1:4:8) With 4cm Size H.g.b. Hand Broken Metal Of Approved Quality From Approved Quarry With Ramming Watering And Curring Etc. Complete Including Cost, Taxes, Royalty Convence Charge Of All Material To Worksite, Supply Of Cement T&p Required Etc. Complete As Per The Direction Of The Engineer-incharge. Brick Work With Fly Ash Brick 25cm X 12cm X 8cm Size Having Crushing Strength Not Less Than 75kg / Cm2 With Dimensional Tolerrance + 8% In Cement Mortar (1:6) In Foundation & Plinth Etc. Complete As Per The Engineer-incharge. 12mm Cement Plaster In Cement Mortar (1:6) Finished Smooth To Brick Work After Racking Out Joints Including Waterring And Curring With Cost, Taxes, Royalty And Conveyance Charges Of All Material To The Worksite And Supply Of All Labour And T&p Required For The Work Etc Complete As Directed By The Engineer-incharge. R.c.c. Work In C.c. (1:2:4) Including Hoisting & Laying & Curring For 28 Days Using 12mm. Size Clean Black Hard Granite Crusher Broken Chips Of Approve Quality And From Approve Quarry Including Cost Taxes Conveyance Charges Of All Materials To The Worksite With Supply Of All Labour And T&p Required For The Work Etc Complete As Directed By The Engineer-incharge. "rigid Smooths Centering And Shuttering For Rcc Works Including False Work And Dismentgalling Then After Casting Including Cot Os Materials Complete. (a) Rcc Walls And Fins Including Attached Pillasters" Labour Charge For M.s. Reinforcement For R.c.c. Work Including Cutting, Bending & Typing The Grills & Placing In Position Including Cost Of Binding Wire 18 To 20 Guage Per Qntl. Including Cost Of Hysd Still Bar (fe 415/ Fe 500) Filling The Foundation And Plinth With Excavated Material As Directed By The Engineer-incharge. Finishing Wall With Water Proofing Cement Paint Of Approved Shade Two Coats To New Work To Give An Even Shade Including Cost Of Cement Paints. Etc. Complete As Per The Direction Of Engineer – In Charge. Writing Charge Of Required Information And Data On Both Side Of The Transperancy Pillar Including Supplying Of Approved Paints And Required Material For Writing Etc. Complete As Per The Direction Of The Engineer-incharge. Supplying Of 160 Mm Dia Unplasticised Rigid Upvc Pipe Ivory Gray In Colour Having Specific Gravity Of 1.40 To 1.46 Gms/cc Of Straight Length Of 6 (six) Meter For Portable Water Supplies Conforming To Is - 4985 / 2000 Of Bis - Amendment - 2 Read With Table - 1 Of Is - Specification Bearing Isi Marks For Working Pressure Ci - I Upvc Pipe To Withstand Pressure Of 2.5 Kgf/sqcm & The Specification And Manufacturer Name Should Be Prominently Marked On Body Of Each Pipe As Per The Latest Amendment Of Is - 4985. It Includes The Cost Of Sockets In Case Of Plain Ended Pipe. Pdi Test ( Both Pre & Post Inspection ) Are To Be Condcuted And Should Be Marked On Body Of Each Pipe And Report Is To Be Obtained From Cipet, Bhubaneswar Necessary Approval Of Authority Including Transportation To Work Site In Complete Shape. Fitting Of Un Plasticised 160mm Dia Pvc Pipe For Following Inside Dia Mtr. For All Classes Of Pipe Including Jointing The Pipe With Solvent Cement By Non-head Application Method Including Fitting And Fixing Of Required No. Of Pvc Tee For Outlet And Pvc Shaddle And Pvc Riser Nipple For Fitting Air Valve, Equal Tee Etc. Complete Including Conveyance Pipe From Village To Worksite And Testing Of Pipe Line Etc. Complete As Per The Direction Of The Engineer-incharge. 7.5 Hp / 5.6 Kw Submersible Pumpset Corpled With Totally Enclosed Water Cooled Squirrel Case Induction Motor With Delivery Discharge 1100 Lpm At 36 Meter Head With S/s Cable, Clamp Clip Etc. Suitable For Operation At 415v + -15%, 3 Phase 50hz A.c. Power Supply As Per Particulars In Annexure. Labour Charges For Installation Of 7.5hp Motor Including Fitting & Fixing Of Base Frame, Fitting & Fixing Suction And Delivery Pipe To Motor, Nr Valve, Foot Valve, Sluice Valve And Other Fitting Materials Including Cutting, Welding And Construction Of Supporting Pillar Etc. Complete As Per The Direction Of The Engineer-incharge. 100 Mm ø Nominal Bore G.i. Pipe Having Wall Thickness 4.5 Mm Electrical Resistance Welded Of Medium Class Confirming To Is - 1239 (pt-1 Of 2004) With Socketed At One End And The Other End Protected With Plastic Thread Protector. The Socket Confirming To Is-1239 (pt-ii/1992) With Latest Amendmewnts In Random Length Of 4 To 7 Mtrs. Each Pipe Should Bear Isi Certification & Manufacturers Name / Trade Mark. 100 Mm Dia G.i. Bend Is No.1239(part-ii/1992) 100 Mm Dia G.i. Flange Is No.6392 / 1971 Cost Of Tw Safe Guard For Stand Includng Labour Charge 100mm Dia Gi Socket Is 1239 (part-ii/1992 ) Cost Of 100 Mm Dia Ms T/w Clamp Cost Of 100 Mm Dia C.i Reflux Valve(nr) 160 Mm X 160 Mm X 160 Mm ø Pvc Equal Tee (w.p. 4 Kgf/cm2) Confirming To Is-4995/1988 With Latest Ammendment 160 Mm ø Pvc End Cap (w.p. 10 Kgf/cm2) Confirming To Is-4995/1988 With Latest Ammendment 5/8 X3" Nut Bolt & Foundation Nut Bolt As Per Is Specification 1/8" Thick Rubber Insertion As Per Is Specification Cost, Supplying Of 160mmx160mmx110mm Dia Weldless G.i.tee (3.6mm Thickness) With Bend, Closing And Opening Arrangement Of Reputed Brand Including All Cost, Conveyance, Cess Etc Complete But Excluding Cost Of Gst Cost Of 160mm×110mm Dia Pvc Reducing Socket. Cost Of 12 Mm Wire Rope Control Pannel With Automatic Star Delta Starter, Sheet Steel Enclosure Suitable For Operation Of Squirrel Cage Induction Motor Up To 10 Hp With 16 Amp (ac -3) Duty Contractor At 415 Volt+6%-15%, 3 Phase, 50 Hz Ac Supply With Over Load Relay Range 6.00 To 9.50 Amp & No Volt Coil With Electronic Timer Suitable For Operation At Voltage Range Of 300 To 440 V. The Starter Should Provide Dependable Protection Against Over Load And Single Phasing Fitted With Volt Meter,ameter,mcb In Complete Shape Including Indicator Lamp 63 Amp Main Switch Triple Pole & Neutral Of Voltage Range 440 Volt Of Re-wirable Fuse And Shall Confirm To Is 4064 Part I & With Isi Mark. 3 X 10 Sqmm Tarpodar Cable Xlpe (cross Link Polyethylin) Conforming To Is: 7098 (part-ii) Including Laying Below .9mtr. Of The Ground And Filling The Excavated Materials Including Watering And Ramming. Cost Of Empty Outdoor Irrigation Panel Board (size 0.45mx0.25mx1.20m) Of 18 Swg (cold Rolled) M.s. Sheet With One Coat Of Red Oxid Primer And Two Coats Of Smoke Gray / Navey Blue Enemel Paint On Both Side ( Inside & Outside) Suitable To Mount 3 Phase Starter, Main Switch And Capacitor Inside The Pannel Board Vertically Over 18 Swg M.s. Sheet. The Pannel Board Should Be Provided With Locking Arrangement And Have Grover On Rear Side For Fixing Motor Hood. The Danger Board Should Be Fixed On The To Of The Pannel Door. 2.50mm2 Submerssible (3 Core) Flat Cable Isi Mark Of Reputed Brand Of Isi Specification Including All Cost, Conveyance, Cess Etc Complete But Excluding Cost Of Gst Construction Of 3 Phase 11 Kv Line As Per Rec Standard Confirming To Ie Rules 1956 With 300 Kg 9 M Long Psc Pole With 80 Sqmm Aaac , 11 Kv "v" Cross Arm, With Required No.of 11 Kv T & C Disc. Insulators In Tension Point & 11 Kv Pin Insulators, Couping & Padding Of Poles. Danger Board At Each Pole, Anti Climbing Devices, Stay Set At Bending Point & Double Stay At End Point With 18 Mm G.i.h.t.stay, Concreting Of Stay With Anchor Plate, Guarding At Road Crossings Etc. Including Cost Of All Materials, Labour Transportation,inspection & Commissioning Etc. Complete. Construction And Erection Of 11 /0.4 Kv , 25 Kva Double Pole Mounted Substation Star Rated Confirming To Re Rules 1956, Mounted On 2.44 Mtr. Long Structure, Supported In 300 Kg 9 Mtr Long Psc Pole,transformer Hard Channel & Top Channel Made Of 2.8 M Long 100 X 50 X 6 Mm M.s.channel, Transformer Belting On 2.80 M Long 50 X 50 X 5 Mm M.s.angle, (all Rec Spn Std.f-3) With All Accessories Like 3 Pole 11 Kv Hg Fuse(f-5)& A.b.switches(f-9) Both Mounted On 2.8 M Long 75 X 40 X 6 Mm M.s.channel And Supported By 1.0 M Long 50 X 50 X 5 Mm M.s.angle, With 3 No. 11 Kv Lightening Arrestors & Distribution Box For 25 Kva S/s, G.i.pipe Earthing With 25x5mm G.i.flats Including Cost Of 25 Kva 11/0.4 K.v.transformer , 35 Sqmm 3 1/2 Core Pvc Cable - 40 Mtr Couping & Padding Of Poles, Danger Board At Each Pole, Anti Climbing Devices & All Other Necessary Fittings I.e Required Size Nuts & Bolts, Brackets, Cable, Cable Sockets, Barbed Fencing ( Size (15'x10') With Constn. Of Retaining Wall, Erection Of Rcc Fencing Post , Sand Filling And Metal Spreading ,fixing Of Iron Grill Gate Etc As Per Cesu Specification Etc. Including Cost Of All Materials, Labour , Transportation Complete With Liasioning For Testing Inspection & Commissioning. Construction Of Boundry Wall Fancing ( Size (15'x10') With Constn. Of Retaining Wall, Erection Of Rcc Fencing Post , Sand Filling And Metal Spreading ,fixing Of Iron Grill Gate Etc For Substation As Per Cesu Specification Etc. Including Cost Of All Materials, Labour , Transportation Complete With Liasioning For Testing Inspection & Commissioning. Electrical Installation With Electrical Materials Such As Pvc Tape, Ampere Tape, 7/20 Pvc Copper Wire, 3/20 Pvc Copper Wire, G.i. Flexible Conduite Pipe, No.6 G.i. Wire, Copper Cable Socket, G.i. Socket And Flange And Petty Materials Required For Electrical Installation Including Fixing Of Td Cable Inside The Earth Trench As Per Direction Of Engineer-in-charge.. Electrical Earthing With Digging Earth Pit Of Size (2 Ft X 2 Ft X 3 Ft ) And Using 1/2 '' G.i Pipe ,no -6 G.i Wire ,cable Socket ,flange , Carcoal, Salt Etc. As Per The Direction Of The Engineer-incharge. 4 Kvr Power Shunt Capasitor 4.0 Mm 2 Pvc Single Core Copper Wire Labour For Drilling A Perfectly Vertical Bore Hole Of Specified Dia For A Specified Depth Below Ground Level In Alluvial Soil Strata By Mud Rotary Rig Drilling As Required To Suit The Site Condition As Per The Direction Of Engineer In Charge Including Use Of Own Rigs With Its Accessories, Tools And Plants And All Consumables (like Coir Rope, Cotton Waste And Bentonite Powder Etc. Complete) Etc. For Lowering Of Finished Bore Suitable For Lowering (minimum 400 Mm Dia.) Of 200mm Dia Gi/pvc Pipe For Housing Fitted With Sockets And With Or Without Well Screen As Per The Necessity For The Soft Medium, Hard And Boulder Formations (. Gi/pvc Casing Pipes If Required By The Contractor To Prevent Collapse Of Over Burden Portion ) Including Lower And Withdrawing Of Casing Pipes After Drilling 200mm To 450mm Dia In Over Burden Portion. For Drilling Of 200 (8”) Dia Pipe. From 0 Mtr. To 100th Meters Supply Of All Labour & T&p For Lowering The Following Sizes Of Pvc Pipes With Or Without Slotted Pipes As Per The Necessity From Ground Level & Fitted & Fixed Up In Perfectly Verticaly Position Inlcuding Cutting & Threading Pipe And Slotted Pipe And Fixing All Jointing Materials Etc. Complete. And Keeping The Top Of The Casing Pipe Threaded Including Plugging Tube Wells To Prevent Entry Of Foreign Materials From Above Excluding Cost Of Fitting & Joining Materials. 200mm Dia Pvc/gi Casing Pipes Cleaning And Developing The Production Well Using Their Own Compressor Continuously Worked Till Clear And Adequate Discharge Is Obtained From The Tube Well Including Supply And Use Of All Necessary Equipments And Labour As Per The Direction Of Engineer-in-charge. Supplying All Materials,labour T & P For Packing The Bore With Washed Gravel Size (p-6) Arround The Well Screen And Pipes In Good Quality Including Cost Of Gravel ,conveyance,royality,etc Complete As Per Direction Engineer-in-charge. (100m Depth) =0.786 X (0.4² - 0.2²) X 100mtr = 9.43 Say 9.5 Cum Supplying All Labour Tools ,plant And Grouting With Cement Bentonite Slurry For Saline Sealing In The Bore Arround 200mm Dia Pvc Casing Pipe Etc All Complete As Per Direction Of Engg In Charge(including Cost Of Cement And Bentonite) Labour Charges For Cutting Transverse Slot On 200 Mm Dia Pvc Pipe With Slot Size 1.5 Mm As Per Specification Threading Charges 8" Pvc Bail Plug 8" Pvc Threaded End Cap Pn-10 200mm X 12" Long Pvc Shot Piece 200mm ø Schedule 80 Casing Pipe (as Per Epm Rate Order No.2877 Dated 05.07.2025) Water Sample Test If Required