Description :
Tenders for Supply of Electrician Trade Tools Equipment - Electrician Screw Driver Thin Stem Insulated Handle 4 Mm X 100 Mm, Electrician Screw Driver Thin Stem Insulated Handle 4 Mm X 250 Mm, Punch Centre 150 Mm X 9 Mm Dia, - Knurled Body, Knife Double Bladed Electrician 100 Mm, Mallet Hard Wood 0.50 Kg, Hacksaw Frame Fixed Type 150 Mm, Limit Switch, Liver Operated 2A 500V, 2-Contacts, Cut Out Relays 16A, 440V, Reverse Current Relays 16A, 440V, Over Load Relays 16A, 440V, Under Voltage Relays 360V-440V, Insulator Pin Type Including Hardware Fitting, Insulator Shackle Types Including Hardware Fitting, Insulator Egg Type Including Hardware Fitting, Insulator Suspension Type Including Hardware Fitting, Load Bank Lamp Or Heater Type, 6 Kw 3 Ph, Brake Test Arrangement With Two Spring Balance 0 To 25 Kg, Thermometer Digital 0 C - 150 C, Fuse Rewire Type, Rheostat 0-25 Ohms 2 Amp, Rheostat 0- 300 Ohms 2 Amp, Rheostat 0-1 Ohms 10 Amp, Rheostat 0-10 Ohms 5 Amp, Low-Pressure Sodium Lamp, Plug Socket, Piano Switch, Lamp Holder, 230 V, 5 A, Bus Bar With Brackets 1 Mtr, Rubber Mat 60 X 120 X 2.5 Cm Or 2Ft X 4Ft X 1Inch, Mini Voltmeter Centre Zero 100-0-100 Mv, Watt Meter Analog 0-1.5- 3 Kw, Watt Meter Digital 1Kw, 230V Digital, Energy Meter 3 Ph 440 V, 15 A, 4 Wire, Three Phase Power Factor Meter Digital 20 Amp, 440 V, Megger -500 Volts Cum Continuity Tester Or Insulation Tester Analog Type, Wheatstone Bridge Complete With Galvanometer And Battery, Ac Starter Resistance Type Starter-For A.C Motors Of 2 To 5 H.P., Direct On Line Starter-For A.C. Motors Of 2 To 5 H.P., Star Delta Strater Manual-For A.C Motors Of 2 To 5 H.P., Star Delta Strater Semi-Automatic-For A.C Motors Of 2 To 5 H.P., Star Delta Strater Automatic-For A.C Motors Of 2 To 5 H.P., Soldering Iron 120 Or 125 Watt 230V, Tempreture Controlled Soldering Iron-50W, 230 V, A.C.Ceiling Fan And Ac Table Fan 1200 Mm. Sweep Single Phase 68 W. 250 V, Motor Pump Electric 1 Hp, Emd Detail, Required, No, Epbg Detail, A. The Emd % Will Be Applicable For Each Schedule/Group Selected During Bid Creation., Splitting, Bid Splitting Not Applied., Mse Purchase Preference, Mii Purchase Preference, 1. Estimated Bid Value Indicated Above Is Being Declared Solely For The Purpose Of Guidance On Emd Amount And For Determining The Eligibility Criteria Related To Turn Over, Past Performance And Project / Past Experience Etc. This Has No Relevance Or Bearing On The Price To Be Quoted By The Bidders And Is Also Not Going To Have Any Impact On Bid Participation. Also This Is Not Going To Be Used As A Criteria In Determining Reasonableness Of Quoted Prices Which Would Be Determined By The Buyer Based On Its Own Assessment Of Reasonableness And
